Enum snap::Error

pub enum Error {
    TooBig {
        given: u64,
        max: u64,
    },
    BufferTooSmall {
        given: u64,
        min: u64,
    },
    Empty,
    Header,
    HeaderMismatch {
        expected_len: u64,
        got_len: u64,
    },
    Literal {
        len: u64,
        src_len: u64,
        dst_len: u64,
    },
    CopyRead {
        len: u64,
        src_len: u64,
    },
    CopyWrite {
        len: u64,
        dst_len: u64,
    },
    Offset {
        offset: u64,
        dst_pos: u64,
    },
    StreamHeader {
        byte: u8,
    },
    StreamHeaderMismatch {
        bytes: Vec<u8>,
    },
    UnsupportedChunkType {
        byte: u8,
    },
    UnsupportedChunkLength {
        len: u64,
        header: bool,
    },
    Checksum {
        expected: u32,
        got: u32,
    },
}

Error describes all the possible errors that may occur during Snappy compression or decompression.

Note that it’s unlikely that you’ll need to care about the specific error reported since all of them indicate a corrupt Snappy data or a limitation that cannot be worked around. Therefore, From<snap::Error> for std::io::Error is provided so that any Snappy errors will be converted to a std::io::Error automatically when using try!.

Variants

TooBig

Fields

given: u64

The size of the given input.

max: u64

The maximum allowed size of an input buffer.

This error occurs when the given input is too big. This can happen during compression or decompression.

BufferTooSmall

Fields

given: u64

The size of the given output buffer.

min: u64

The minimum size of the output buffer.

This error occurs when the given buffer is too small to contain the maximum possible compressed bytes or the total number of decompressed bytes.

Empty

This error occurs when trying to decompress a zero length buffer.

Header

This error occurs when an invalid header is found during decompression.

HeaderMismatch

Fields

expected_len: u64

The total number of decompressed bytes expected (i.e., the header value).

got_len: u64

The total number of actual decompressed bytes.

This error occurs when there is a mismatch between the number of decompressed bytes reported in the header and the number of actual decompressed bytes. In this error case, the number of actual decompressed bytes is always less than the number reported in the header.

Literal

Fields

len: u64

The expected length of the literal.

src_len: u64

The number of remaining bytes in the compressed bytes.

dst_len: u64

The number of remaining slots in the decompression buffer.

This error occurs during decompression when there was a problem reading a literal.

CopyRead

Fields

len: u64

The expected length of the copy (as encoded in the compressed bytes).

src_len: u64

The number of remaining bytes in the compressed bytes.

This error occurs during decompression when there was a problem reading a copy.

CopyWrite

Fields

len: u64

The length of the copy (i.e., the total number of bytes to be produced by this copy in the decompression buffer).

dst_len: u64

The number of remaining bytes in the decompression buffer.

This error occurs during decompression when there was a problem writing a copy to the decompression buffer.

Offset

Fields

offset: u64

The offset that was read.

dst_pos: u64

The current position in the decompression buffer. If the offset is non-zero, then the offset must be greater than this position.

This error occurs during decompression when an invalid copy offset is found. An offset is invalid if it is zero or if it is out of bounds.

StreamHeader

Fields

byte: u8

The chunk type byte that was read.

This error occurs when a stream header chunk type was expected but got a different chunk type. This error only occurs when reading a Snappy frame formatted stream.

StreamHeaderMismatch

Fields

bytes: Vec<u8>

The bytes that were read.

This error occurs when the magic stream headers bytes do not match what is expected. This error only occurs when reading a Snappy frame formatted stream.

UnsupportedChunkType

Fields

byte: u8

The chunk type byte that was read.

This error occurs when an unsupported chunk type is seen. This error only occurs when reading a Snappy frame formatted stream.

UnsupportedChunkLength

Fields

len: u64

The length of the chunk encountered.

header: bool

True when this error occured while reading the stream header.

This error occurs when trying to read a chunk with an unexpected or incorrect length when reading a Snappy frame formatted stream. This error only occurs when reading a Snappy frame formatted stream.

Checksum

Fields

expected: u32

The expected checksum read from the stream.

got: u32

The computed checksum.

This error occurs when a checksum validity check fails. This error only occurs when reading a Snappy frame formatted stream.

Trait Implementations

impl Clone for Error

fn clone(&self) -> Error

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for Error

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Display for Error

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Error for Error

fn source(&self) -> Option<&(dyn Error + 'static)>

The lower-level source of this error, if any.

fn description(&self) -> &str

👎Deprecated since 1.42.0: use the Display impl or to_string()

fn cause(&self) -> Option<&dyn Error>

👎Deprecated since 1.33.0: replaced by Error::source, which can support downcasting

fn provide<'a>(&'a self, demand: &mut Demand<'a>)

🔬This is a nightly-only experimental API. (error_generic_member_access)

Provides type based access to context intended for error reports.

impl From<Error> for Error

fn from(err: Error) -> Error

Converts to this type from the input type.

impl PartialEq<Error> for Error

fn eq(&self, other: &Error) -> bool

This method tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

This method tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Eq for Error